According to the management of medium-and long-term weather forecast, in case of continuous low temperature, the temperature of the mushroom house / shed should be kept above 8 °C ~ 10 °C. The main measures for heat preservation and warming include: thickening the roof cover at night; hanging blankets on doors; closing doors and windows for heat preservation in the morning and evening; opening doors and windows around noon in sunny days; opening only leeward vents for short-term ventilation in rainy and snowy weather; in cold or windy weather, close doors, windows and vents to prevent cold air from attacking. When the weather is fine, open the cover to increase the temperature of the light, when the light is strong, it is best to set up a sunshade net under the greenhouse film and above the bacterial stick to protect the light and heat. If there are heating facilities such as hot air stove, the temperature of the mushroom room / shed can be increased by heating, but attention should be paid to prevent the smoke from being discharged into the shed and cause poisoning. In addition, the ditch cleaning and drainage of the mushroom shed should also be done to reduce the humidity in the greenhouse in the rainy season and improve the mushroom quality.
Automobile hot plate welding machine includes: automobile lamp hot plate machine, automobile bumper hot plate welding machine, automobile water hydrant hot plate machine, automobile oil kettle hot plate machine, automobile storage battery hot plate machine, automobile dashboard welding machine, automobile water tank hot plate machine, steering light hot plate welding machine, automobile glove box hot plate welding machine, automobile fuel tank hot plate welding machine, automobile bumper hot plate machine, automobile carbon tank hot plate welding machine, automobile PP plastic hot plate machine, automobile Automobile rear wing hot plate welding machine, automobile horn hot plate welding machine, automobile central panel hot plate machine, automobile speaker hot plate machine, automobile dustproof cover hot plate welding machine, automobile sunshade hot plate welding machine and pneumatic automobile hot plate machine.
To maintain the battery, be sure to bury the battery deep under the protection. Other parts of the vehicle include some air conditioners, lamps, etc., do not directly maintain the vehicle in accordance with the requirements, should rotate the air conditioner (such as light bulbs) and rotate the air conditioner clockwise several degrees. Open the sunshade of the car body in summer, then separate the air conditioner from high and low, and then drive the car to the lower position, two laps, two laps up, in the design of the branches to find the place of ventilation, the electric warm wind can be determined. The maintenance time of each part of the new car in all directions is 15 minutes, which can quickly find out the good effect in a short time. The process of each maintenance is: every delivery inspection, to the highway, any automatic car driver must master the vehicle maintenance knowledge, must not blindly reduce fuel consumption.
Guangzhou Green long awning Technology Co., Ltd. was founded in 1997, is the first company in China to focus on outdoor sunshade. For more than 20 years, GE Lulang has been integrating the spirit of innovation into the brand, opening an epoch-making chapter in the domestic sunshade brand. As early as not long after the establishment of GE Lulang, the sunshade industry was still in a small and miscellaneous situation, even without a real sunshade brand. Under such conditions of the times, GE Lulang, under the leadership of founder Fang Guiping, took the lead in brand innovation and established a real outdoor sunshade brand. In 2012, GE Lulang established the “awning Greenland” brand operation strategy, comprehensively introduced CIS brand construction, and created a new brand strategy situation.
The interior design mainly includes dashboard, steering wheel, seat, seat belt, airbag, carpet, sidewall interior decoration, sunshade panel, handrail, car rearview mirror and so on. The main design of exterior parts includes front and rear bumper, glass, door anti-collision decoration strip, intake grille, luggage rack, skylight, rearview mirror, door mechanism and accessories and sealing strip. At this stage, VR allows designers to place virtual dolls in digital car models to verify the accessibility of each interior and man-machine interface. This feature increases the cost of trial and error for automakers before they go into production without VR, while VR perfectly solves the problem of long testing cycles for all ergonomics and car interiors.